6 inch Premium Chimney System Pack - House Internal

The Chimney Pack is used when you are running the flue internally through your house. All the parts you require are included in the Chimney Pack.

CONTENTS
The pack contains:-
1 x Stove Pipe
1 x DT - Adaptor To Stove Pipe
5 x DT - Pipe 1000mm
1 x DT - Pipe 500mm
1 x DT - Terminal
1 x RES 2 EPDM Flashing
1 x DT - Storm Collar
2 x DT - Floor Support
1 x DT - Roof Support
4 x DT - Ventilated Firestop Plate
7 x DT - Locking Bands
1 x Chimney Notice Plate
1 x Carbon Monoxide Alarm
1 x High Temperature Sealant

APPLICATION
For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil boiler, condensing boilers and any solid fuel appliances.

CONSTRUCTION
Outer skin is made from 304 grade stainless steel and is 0.5mm thick. Inner skin is made from 316 grade stainless steel and is 0.5mm thick. Insulation is compressed rockwool which is injected into the flue giving a density of 180kg per cubic metre. All parts are fully welded – making DT suitable for condensing appliances.
Distance to combustibles is 50mm.

APPROVALS
DT is HETAS Approved and is CE marked.
Designation Number

is EN1856-1 T600 N1 D V2 L50050 G50.

7 inch Classic Twinwall - Rain Cap Ø 175

The Rain Cap fits to the top of the flue system to stop any water coming down the flue. Ideal for use on oil or solid fuel installations in non-open areas..
This item comes with a FREE Locking Band.

APPLICATION
For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil boiler and any solid fuel appliances.

CONSTRUCTION
Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 128kg per cubic metre. All parts are fully welded.
Distance to combustibles is 60mm.

APPROVALS
KC is HETAS Approved and is CE marked.
Designation Number
EN1856-1 T600 N1 D V2 L50040 G60.

INSTALLATION
KC Twin Wall Insulated Chimney parts are secured together by using a Locking Band (supplied).
Make sure that you keep a distance of 60mm from the outside of the flue to any combustible material (wood, plaster board).

5 inch 90 Elbow c/w Door Black enamel finish

90 degree elbow with access door for sweeping, you need to buy a gasket separately

APPLICATION
Suitable for pellet appliances with temperatures up to 750 degrees C.
Pellet Stove Pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System.
Pellet Stove Pipe should NOT be used to pass through ceilings or wall.

CONSTRUCTION
Pellet Stove Pipe is a single skin flue system manufactured in zero carbon steel with vitreous enamel coating in a matt black finish.
Suitable for Pellet fuel appliances with temperatures up to 750 degrees C.

INSTALLATION
You should not install a piece of Black Stove Pipe within 3 times the diameter of the flue from combustible material, e.g. wood, plaster boards, etc.
A 5 inch (125mm) diameter piece of Black Stove Pipe should be 15 inches (375mm) away from combustible materials.
When installing make sure Black Stove Pipe is installed the correct way up - the smaller diameter should always be pointing downward.
This is because all the condensates will stay within the flue system and not pass to the outside of Black Stove Pipe.
Each joint should be coated with a jointing compound (fire cement or high temperature silicone sealant).This makes sure that no condensate can escape and spoil the appearance of the pipe.

Flue Liner Installation Kit 3 7 inch

Installation Pack No. 3, ALL YOU NEED IN ONE BOX FOR USE WITH 180mm diameter multifuel flex.

 

APPLICATION
Use this pack when you DO NOT want to remove the existing chimney pot.

PACK CONTAINS
1 x Stainless Steel Pot Hanging Cowl with Mesh - Ø180mm
1 x Nose Cone - Ø180mm
1 x Adaptor to Black Pipe or Single Wall Flue - Ø180mm
1 x Chimney Notice Plate

6 inch Connecting Adaptor - Sump Adaptor

The Sump Adapter is used to connect to the bottom of a chimney stack which has a clay liner installed, and a chimney flue liner is not being installed. It has a stainless steel plate 325mm x 325mm with a downwards facing spigot which fits into single wall pipe.

APPLICATION
Clay Pot Adapters are used to connect to the bottom of a chimney stack which has a clay liner installed, and a chimney flue liner is not being installed.
The existing clay liner must be smoke tested to prove it is good condition, before this method of connection is used on an installation.

CONSTRUCTION
Made from 1mm thick stainless steel grade 316.

INSTALLATION
Place the plate up towards the underside of the stack. Mark where the Adaptor can be securely screwed into the surrounding stack. Drill, screw and secure into the surrounding stack.
Finish off with Fire Cement and Fire Rope to make a good seal around the square plate of the adaptor.
The single wall pipe can then placed over the spigot of the adaptor.
Again finish off with Fire Cement and/or Fire Rope to make a good seal.

Log Store (self assembly) W 1200mm x D 560mm x H 1560mm

Log Store made from FSC Certified tanalised timber. Slotted sides to improve drying times.

FSC Certified Timber.
Hand made in wales.
Flat Packed.
Easy to assemble complete with instructions.
Tanalised weatherproof timber.
Slotted sides to improve drying times.
Sturdy construction.
Long life.
W x H x D (1200mm x 1560mm x 550mm)

Flue Liner 316L for Gas and Oil (316L Grade) 8 inch

Suitable for use on appliances fired by gas ( as specified by the fire manufacturer ), and oils up to 28 second.

APPLICATION
A single skin flexible flue liner suitable for relining within a masonry chimney. Suitable for use on appliances fired by gas ( as specified by the fire manufacturer ), and oils up to 28 second, and designed to accommodate temperatures not exceeding 260°C.

CONSTRUCTION
The flue liner is manufactured from 316L grade stainless steel and is 0.10mm thick. The flue liner has five convoluteions between each seam. The Flue Liner seam is folded in three planes to give a TRIPLELOCK seal.

APPROVAL
TRIPLELOCK Flue Liner is Kitemarked to BS 715 and has been approved and tested to BS EN 1856:2

DESIGNATION NUMBER
BS EN 1856:2 T250 N1 D V3 L50010 G

INSTALLATION - CHECK LIST
1.Make sure the liner will go down the chimney (this can be done by pulling down a small section of the diameter liner you will be using)
2.Sweep your chimney.
3.Check you pot is in good condition, if you are NOT using a suspended cowl then remove the pot from the stack.

INSTALLATION
Flue Liner should always be fitted from the top.
Secure a piece of string (at least the same length as the Flue Liner to the Nose Cone (order separately).
Now attach the Nose Cone onto the end of the Flue Liner
Pull the liner down the chimney using the string and at the same time have someone at the top of the chimney feeding the Flue Liner down, once the Flue Liner is fitted remove the Nose Cone. If necessary cut the flue liner to length, and secure the liner at the top using the clamp plate. Ensure 75mm of the flue liner projects above the clamp plate so that the terminal can be located and secured.
Secure and seal the flue liner to a register plate, which closes off the appliance recess. Alternatively the end of the flue liner can be sealed into flue pipe or a Flue Gas Collector or Flue Box.
Terminate the flue liner by securley fitting the terminal to the projecting section of flue liner. Apply a suitable cement as a seal and weather proof render.

MAINTENANCE
It is recommended that chimneys serving gas and oil appliances be swept and maintained as frequently as necessary but at least once a year.

45° Tee c/w Clean Out Door 7 inch

A 45° / 135° Tee and Tee Cap.
A Joint Clamp Band is required to fix this item to the next.

APPLICATION
Suitable for gas, oil and solid fuel appliances with temperatures up to 750 degrees C.
1mm Stainless Steel Stove pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System.
1mm Stainless Steel Stove Pipe should NOT be used to pass through ceilings or wall.

CONSTRUCTION
1mm Stainless Steel Stove Pipe is a single skin flue system manufactured in 316 grade stainless steel and is 1mm thick.
Suitable for gas, oil and solid fuel appliances with temperatures up to 750 degrees C

INSTALLATION
You should not install a piece of 1mm Stainless Steel Stove Pipe within 3 times the diameter of the flue from combustible material, e.g. wood, plaster boards, etc.
A 5 inch (125mm) diameter piece of 1mm Stainless Steel Stove Pipe should be 15 inches (375mm) away from combustible materials.
When installing make sure 1mm Stainless Steel Stove Pipe is installed the correct way up - the smaller convoluted diameter should always be pointing downward.
This is because all the condensates will stay within the flue system and not pass to the outside of Stove Pipe.
Each joint should be coated with a jointing compound (fire cement or high temperature silicone sealant).This makes sure that no condensate can escape and spoil the appearance of the pipe.
Each part should then be secured by using a Joint Clamp Band.

MAINTENANCE
You should make provision for inspecting and cleaning the chimney. This is particularly important on solid fuel applications.
You can acheive this by installing a pipe with an access door.
It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

135º Tee Ø 175 7 inch

The 135° Tee is used when you need a cleaning access at the base of the chimney. It is the first piece installed on the external wall and allows for ease cleaning of the flue. The 135° Tee is shaped in such away that it does not restrict the flue gases.

This item comes with a 2 FREE Locking Bands.

 

Flue Liner Installation Kit 1 6 inch

Installation Pack No. 1, ALL YOU NEED IN ONE BOX FOR USE WITH 150mm diameter multifuel flex.

 

APPLICATION
Use this pack when you want to remove the existing chimney pot - and then replace it when the flue liner is installed. You will probably need to install a cowl or terminal for your chimney to offer some weather and bird protection.

PACK CONTAINS
1 x Top Plate - Ø150mm
1 x Top Clamp - Ø150mm
1 x Top Insert - Ø150mm
1 x Nose Cone - Ø150mm
1 x Adaptor to Black Pipe or Single Wall Flue - Ø150mm
1 x Chimney Notice Plate

Log Store (self assembly) W 1200mm x D 560mm x H 1560mm

Log Store made from FSC Certified tanalised timber. Slotted sides to improve drying times.

Flue Liner Installation Kit 6 - 7 inch

Installation Pack No. 6, ALL YOU NEED IN ONE BOX FOR USE WITH 180mm diameter multifuel flex.

 

APPLICATION
Use this pack when you DO NOT want to remove the existing chimney pot.

PACK CONTAINS
1 x Stainless Steel Pot Hanging Cowl with Mesh - Ø180mm
1 x Nose Cone - Ø180mm
1 x Increasing Adaptor to Black Pipe or Single Wall Flue - Ø150mm SW to Ø180mm Flex
1 x Chimney Notice Plate

MI Rota-Top 200 (Stainless Steel Top and Base) Bolt Fix

Suitable for chimney sizes 125mm (5 inch) to 250mm (10 inch). Wind driven revolving chimney cowl. Stainless steel construction with fully cast base. Fully enclosed brass bearings. Can be used on chimneys with appliances fired by gas, oil or solid fuel. Claw bolt fixing for added security.

Chimney Cowls - Spark Arrester (terracotta) - bolt fix



A twin meshed cowl for use with shingle or thatched properties. One size fits all (150mm - 250mm).

Chimney System Packs 5 inch premium - Bungalow External



The Chimney Pack is used when you are running the flue outside your Bungalow. All the parts you require are included in the Chimney Pack.

CONTENTS
The pack contains:-
1 x Stove Pipe
1 x 45° Bend Stove Pipe
1 x DT - Adaptor To Stove Pipe
1 x DT - Pipe 500mm
1 x DT - Adjustable Length
1 x DT - 135° Tee
1 x DT - Tee Cap
1 x DT - Wall Support Bracket
1 x DT - Wall Support Plate
2 x DT - 45° Bend
1 x DT - Pipe 1000mm
2 x DT - Pipe 250mm
1 x DT - Terminal
10 x DT - Locking Bands
1 x DT - Wall Band
1 x Chimney Notice plate
1 x Carbon Monoxide Alarm
1 x High Temperature Sealant

APPLICATION
For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil boiler, condensing boilers and any solid fuel appliances.

CONSTRUCTION
Outer skin is made from 304 grade stainless steel and is 0.5mm thick. Inner skin is made from 316 grade stainless steel and is 0.5mm thick. Insulation is compressed rockwool which is injected into the flue giving a density of 180kg per cubic metre. All parts are fully welded – making DT suitable for condensing appliances.
Distance to combustibles is 50mm.

APPROVALS
DT is HETAS Approved and is CE marked.

Designation Number is
EN1856-1 T600 N1 D V2 L50050 G50.

Chimney System Pack - 5 inch Chimney Removed or Lowered

The Chimney Pack is used when your chimney stack has been lowered beneath your roof line. This happens when your existing masonry chimney becomes unsafe. This Chimney Pack allows you to build the chimney off the top of the existing stack, and through the roof. All parts you require are included in the Chimney Pack.

 

CONTENTS
The pack contains:-
1 x DT - Wall Support Plate
2 x DT - Pipe 1000mm
1 x DT - Pipe 500mm
1 x DT - Roof Support
1 x RES 2 EPDM Flashing
1 x DT - Storm Collar
4 x DT - Locking Band
1 x High Temperature Sealant
1 x DT - Terminal

APPLICATION
For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil boiler, condensing boilers and any solid fuel appliances.

CONSTRUCTION
Outer skin is made from 304 grade stainless steel and is 0.5mm thick. Inner skin is made from 316 grade stainless steel and is 0.5mm thick. Insulation is compressed rockwool which is injected into the flue giving a density of 180kg per cubic metre. All parts are fully welded – making DT suitable for condensing appliances.
Distance to combustibles is 50mm.

APPROVALS
DT is HETAS Approved and is CE marked.

Designation Number is
EN1856-1 T600 N1 D V2 L50050 G50.

Chimney System Packs 6 inch - Flex Reline with Chimney Removed

The Chimney Pack is used when your chimney stack has been lowered beneath your roof line, and you are required to re-line the remaining chimney stack with a flexible liner. This happens when your existing masonry chimney becomes unsafe. This Chimney Pack allows you to build the chimney off the top of the existing stack, and through the roof. All the parts you require are included in the Chimney Pack, but the correct length of flue liner must be ordered seperately.

 

CONTENTS
The pack contains:-
1 x Stove Pipe
1 x MAE Stove Pipe To Flex Adaptor
1 x Register Plate
1 x DT - Adaptor To Single Wall
1 x DT - Wall Support Plate
2 x DT - Pipe 1000mm
1 x DT - Pipe 500mm
1 x DT - Roof Support
1 x RES 2 EPDM Flashing
1 x DT - Storm Collar
5 x DT - Locking Band
1 x High Temperature Sealant
1 x DT - Terminal

APPLICATION
For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil boiler, condensing boilers and any solid fuel appliances.

CONSTRUCTION
Outer skin is made from 304 grade stainless steel and is 0.5mm thick. Inner skin is made from 316 grade stainless steel and is 0.5mm thick. Insulation is compressed rockwool which is injected into the flue giving a density of 180kg/m³. All parts are fully welded – making DT suitable for condensing appliances.
Distance to combustibles is 50mm.

APPROVALS
DT is HETAS Approved and is CE marked.

Designation Number is
EN1856-1 T600 N1 D V2 L50050 G50.

Log Store (self assembly) W 1200mm x D 560mm x H 1560mm

Log Store made from FSC Certified tanalised timber. Slotted sides to improve drying times.

 

FSC Certified Timber.
Hand made in wales.
Flat Packed.
Easy to assemble complete with instructions.
Tanalised weatherproof timber.
Slotted sides to improve drying times.
Sturdy construction.
Long life.
W x H x D (1200mm x 1560mm x 550mm)

1000mm Pipe



Suitable for gas, oil and solid fuel appliances with temperatures up to 750 degrees C.
1mm Stainless Steel Stove pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System.

Chimney System Pack - 6 inch Flex Reline with Chimney Removed

The Chimney Pack is used when your chimney stack has been lowered beneath your roof line, and you are required to re-line the remaining chimney stack with a flexible liner. This happens when your existing masonry chimney becomes unsafe. This Chimney Pack allows you to build the chimney off the top of the existing stack, and through the roof. All the parts you require are included in the Chimney Pack, but the correct length of flue liner must be ordered seperately.

Installation - Fire Cement - Black - 2Kg Tub

A black in colour adhesive cement, withstands heat up to 1200°C. 2Kg tub

45 Elbow Black enamel finish



45 degree elbow used to make a 45 degree change in direction from the vertical, you need to buy a gasket seperately

Disused Chimney Cap (terracotta) - strap fix

The Chimney Capper chimney caps off the unused chimneys. One size fits all (150-250mm). Comes jubilee strap type fixing

Pipe 500mm Ø 175

APPLICATION
For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil boiler and any solid fuel appliances.

CONSTRUCTION
Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 128kg/m³. All parts are fully welded.
Distance to combustibles is 60mm.

APPROVALS
KC is HETAS Approved and is CE marked.
Designation Number
EN1856-1 T600 N1 D V2 L50040 G60.

INSTALLATION
KC Twin Wall Insulated Chimney parts are secured together by using a Locking Band (supplied).
Make sure that you keep a distance of 60mm from the outside of the flue to any combustible material (wood, plaster board).

Chimney System Packs

Flex Reline with Chimney Removed (6 inch) 



The Chimney Pack is used when your chimney stack has been lowered beneath your roof line, and you are required to re-line the remaining chimney stack with a flexible liner. This happens when your existing masonry chimney becomes unsafe. This Chimney Pack allows you to build the chimney off the top of the existing stack, and through the roof. All the parts you require are included in the Chimney Pack, but the correct length of flue liner must be ordered seperately.

CONTENTS
The pack contains:-
1 x Stove Pipe
1 x MAE Stove Pipe To Flex Adaptor
1 x Register Plate
1 x DT - Adaptor To Single Wall
1 x DT - Wall Support Plate
2 x DT - Pipe 1000mm
1 x DT - Pipe 500mm
1 x DT - Roof Support
1 x RES 2 EPDM Flashing
1 x DT - Storm Collar
5 x DT - Locking Band
1 x High Temperature Sealant
1 x DT - Terminal

 

APPLICATION
For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil boiler, condensing boilers and any solid fuel appliances.

 

CONSTRUCTION
Outer skin is made from 304 grade stainless steel and is 0.5mm thick. Inner skin is made from 316 grade stainless steel and is 0.5mm thick. Insulation is compressed rockwool which is injected into the flue giving a density of 180kg/m³. All parts are fully welded – making DT suitable for condensing appliances.
Distance to combustibles is 50mm.

 

APPROVALS
DT is HETAS Approved and is CE marked.