Install Packs - Installation Packs contain everything you need to install a flue liner to HETAS recommendations

Install Packs - Installation Packs contain everything you need to install a flue liner to HETAS recommendations

Installation Packs can include Top Plate, Top Clamp, Protection Sleeve, Nose Cone, Chimney Notice Plate, Adapter to single wall pipe, Rain Cap, Pot Hanging Cowl with Mesh (stainless steel finish), Protection Sleeve, Increasing adapter to single wall pipe.

Comes in diameters: 125mm, 150mm, 180mm and 200mm.

Ancillaries - Rain Cap, Pot Hanging Cowls, Protection Sleeve Rain Cap, Top Plate, Top Clamp, Protection Sleeve, etc

Ancillaries - Rain Cap, Pot Hanging Cowls, Protection Sleeve Rain Cap, Top Plate, Top Clamp, Protection Sleeve, etc

Pot Hanging Cowls

USES
The Pot Hanging Cowls has two main functions :-
(1) Allows the chimney liner to be installed without removing the pot
(2) The straps on the outside provide a clamping system to the chimney pot.
Pot Hangers with integral cowls also provide rain protection or even prevent anti downdraught problems at the top of the stack.

INSTALLATION
To attach the flue liner to the Pot Hanger, release the inner jubille clip and push the 3 straps away from the centre mandrel. Insert the mandrel into the flue liner and push the flue liner up fully until it won't move anymore. Now tighten the jubille clip.

Install the flue liner as per normal fitting instructions.

Once the liner is in position release the outer jubille clip, now let the Hanger drape over the chimney pot. Now tighte the jubille clip so it is securely held against the chimney pot.

AVAILABILITY
POT HANGER (20-D-PHS)
Only available in raw stainless steel finish.
Comes in the following flue liner diameters 125mm, 150mm, 180mm and 200mm
POT HANGING COWL WITH MESH (20-D-PHCM)
Only available in raw stainless steel finish.
Comes in the following flue liner diameters 125mm, 150mm, 180mm and 200mm
POT HANGING COWL WITH MESH TERRACOTTA (20-D-PHCMT)
Available in stainless steel with terracotta powder coated finish.
Comes in the following flue liner diameters 125mm, 150mm, 180mm and 200mm
POT HANGER with ANTI-DOWN DRAUGHT COWL (20-D-PHAD)
Only available in raw stainless steel finish.
Comes in the following flue liner diameters 125mm, 150mm, 180mm and 200mm
POT HANGER with ANTI-DOWN DRAUGHT COWL TERRACOTTA (20-D-PHADT)
Available in stainless steel with terracotta powder coated finish.
Comes in the following flue liner diameters 125mm, 150mm, 180mm and 200mm

Triplelock Gas and Oil Introduction, Installation, Application, Approvals, Designation, Packaging, etc.

Triplelock Gas and Oil Introduction, Installation, Application, Approvals, Designation, Packaging, etc.

TRIPLELOCK flexible flue liner is designed for use with gas and 28-second oil fired appliances, and to accomodate temperatures not exceeding 260 degrees.

Manufactured in a single skin of 316L stainless steel. It has a rolled and crimped seam featuring a triple locking process.

Comes with a range of accessories, and is available in 100mm, 125mm, 150mm, 180mm, 200mm, 250mm, 300mm, 350mm and 400mm diameters.

HD Flex Introduction, Application, Approvals, Designation, Installation & Prep, etc

HD Flex Introduction, Application, Approvals, Designation, Installation & Prep, etc

HD-FLEX (Heavy Duty) is a flexible twin-skinned stainless steel flue lining with a smooth inner wall, and a riged convoluted outer wall (to aid bending).

As the name suggests the flue liner is manufactured from two strips of raw material, the wider of the two forms the convoluted outer, whilst the inner froms the smooth inner wall. The joint or seam is constructed using a complex folded seam which uses more material than other systems, this then makes the joint extremely strong.

The system has been designed to upgrade existing chimneys which have failed, or for used to increase the performance of the flue.

Manufactured in two skins of either 316L grade
or two skins of 904L grade
or inner skin of 904L and outer skin of 316L

Comes with a range of accessories, and is available in 125mm, 150mm, 180mm and 200mm diameters.

Quattro DS Installation & Prep, Introduction, Application, Approvals, Designation, etc

Quattro DS Installation & Prep, Introduction, Application, Approvals, Designation, etc

Quattro-DS (double strip) is a flexible twin-skinned stainless steel flue lining with a smooth inner wall, and a riged convoluted outer wall (to aid bending).

As the name suggests the flue liner is manufactured from two strips of raw material, the wider of the two forms the convoluted outer, whilst the inner froms the smooth inner wall. The joint or seam is construtructed using a triplelock dovetail folded seam, to make this joint extremely strong.

The system has been designed to upgrade existing chimneys which have failed, or for used to increase the performance of the flue.

Manufactured in two skins of either 316L grade (System MF5),
or two skins of 904L grade (System MF18H),
or inner skin of 904L and outer skin of 316L (System MF18M)

Comes with a range of accessories, and is available in 100mm, 125mm, 150mm, 180mm, 200mm, 250mm, 300mm, 350mm and 400mm diameters.

Quattro SS Introduction, Application, Approvals, Designation, Packaging.

Quattro SS Introduction, Application, Approvals, Designation, Packaging.  

Quattro-SS (single strip) is a flexible twin-skinned stainless steel flue lining with a smooth inner wall and a convoluted riged outer wall (to aid bending).

As the name suggests the flue liner is made from strip of raw material, which is bent in half to form a smooth inner wall, and a convoluted outer wall. Being formed from one peice of steel means the joint or seam (which is the weakest point) is extremely strong.

The system has been designed to upgrade existing chimneys which have failed, or for used to increase the performance of the flue.

Manufactured in two skins of either 316L grade (System MF35) or 904L grade (System MF36)

Comes with a range of accessories, and is available in 80mm, 100mm, 125mm, 150mm, 180mm, 200mm, 250mm and 300mm diameters. 

Flue Liner Regulations, Warranties, 316L & 904L & MIX, Size Of Lining.

Flue Liner Regulations, Warranties, 316L & 904L & MIX, Size Of Lining.

316L/316L Grade:- (System MF35)
This liner uses 316L grade stainless steel for both the inner and the outer skins. It is suitable for use on appliances burning the following fuels:-
GAS, COAL, OIL, COKE, WOOD and CURED DRY PEAT

904L/316L Grade:- (System MF18M)
This liner uses 904L grade stainless steel for the inner and 316L grade stainless steel for the outer skin. It is suitable for use on appliances burning the following fuels:-
GAS, COAL, OIL, COKE, WOOD, CURED DRY PEAT and SMOKELESS FUELS.
This is the most economical liner for use with smokeless fuels.

904L/904L Grade:- (System MF36)
This liner uses 904L grade stainless steel for both the inner and the outer skins, the best chimney liner you can buy. It is suitable for use on appliances burning the following fuels:-
GAS, COAL, OIL, COKE, WOOD, CURED DRY PEAT and SMOKELESS FUELS.
Recommended particularly if you are slumbering your appliance overnight, or for heavy usage.

Chimney liners can be used on open fires as well as closed appliances like wood burning and multi fuel stoves.